STEINEL IS D 360 Specifications download pdf (Page 8)

15

Malfunction Cause Remedy

Without power ■ Fuse faulty,

not switched ON

■ Short circuit

■ New fuse, switch ON

mains switch, check lead

with a voltage detector

■ Check connections

Does not switch ON ■ Twilight setting in

night-time mode during

daytime operation

■ Bulb faulty

■ Power switch OFF

■ Fuse faulty

■ Detection zone not targeted

■ Adjust setting

■ Replace light bulbs

■ Switch ON

■ New fuse, check

connection if necessary

■ Re-adjust

Does not switch OFF ■ Continued movement in

the detection zone

■ Light is in detection zone

and keeps switching ON

as a result of temperature

change

■ Check zone and re-adjust

or shroud if necessary

■ Change zone, or apply

shroud

Keeps switching ON/OFF ■ Lamp being operated

in the detection zone

■ Animals moving in the

detection zone

■ Adjust zone, shroud or

increase distance

■ Adjust zone, or apply

shroud

Switches ON when it

should not

■ Wind moves trees and

bushes in the detection

zone

■ Cars in the street are

being detected

■ Sudden change in temp-

erature due to weather

(wind, rain, snow) or air

expelled from fans, open

windows

■ Adjust zone or

apply shroud

■ Adjust zone or

apply shroud

■ Adjust zone, change

installation site

LED flashes rapidly ■ Overload protection

activated

■ Switch OFF unit and

switch ON again after

cooling down

Troubleshooting

14

Sensor operation

1) Switch light ON (when light is OFF):

Turn switch OFF and ON once.

Light stays ON for the period selected.

2) Switch light OFF (when light is ON):

Turn switch OFF and ON once.

The light goes out or switches over to

sensor mode.

Manual override function

Manual override

1) Activate manual override:

Turn switch OFF and ON twice. The lamp is

set to stay on for 4 hours (red LED lights up

behind the lens). Then it returns automatically

to sensor mode (red LED off).

2) Deactivate manual override:

Turn switch OFF and ON once. The light goes

out or switches over to sensor mode.

If a mains switch is installed in the mains supply

lead, the light is capable of the following func-

tions in addition to the simple ON/OFF function:

Important: The switch should be operated

several times in rapid succession.

Technical specifications

Dimensions (H x Ø): 82 x 51 mm

Output: max. 1000 W (filament bulbs)*

max. 5 AX (fluorescent lamps)*

Switching capacity: 50 – 240 V~ / 5 A

Connection: 230 – 240 V/50 Hz

Angle of coverage: 360° with 180° angle of aperture

Reach: 8 m max. all round

Sensor system: 10 detection zones, 720 switching zones

Time setting: 5 sec. – 20 min.

Twilight setting: 2 – 2000 lux

Manual override: 4 hrs. selectable

Enclosure (top/bottom): IP 20

Temperature range: -20 °C to +50 °C

*VDE tested

Reach setting / adjustment

With an assumed mounting height of 2.5 m,

the maximum reach of the sensor is 8 m. The

detection zone can be optimally adjusted ac-

cording to needs. The shroud provided can be

used for masking out any number of lens seg-

ments to shorten reach as required. This pre-

vents the light from being activated uninten-

tionally, e.g. by cars, passers-by etc. and

allows you to target danger spots. The shroud

can be separated along the pre-grooved div-

isions in the vertical and horizontal directions

and applied to the lens.





GB

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 63 64

Comments to this Manuals

No comments