STEINEL NEO2 Operations Instructions download pdf (Page 6)

- 10 - - 11 -

System components

a ON/OFF button

b feed trigger

c LED indicator

d socket for charging cable

e USB charger

f glue stick

Operating principle

and handling

■ Before using for the first time, fully

charge the battery (2-3 hours) so

as to prolong its life. (see Charging/

Operation)

■ Insert glue stick into rear heating

duct.

■ When using the tool for the first time,

press the trigger several times to fill

the heating chamber with adhesive. It

may also be necessary to give the glue

stick a short push to help it move in.

■ To prevent the applicator from being

switched ON unintentionally, you

must press the button for approx.

2 sec. Green LED flashes for 15 sec.

■ Press trigger and apply glue to one

side.

■ Firmly press together the materials

being glued, correcting alignment if

necessary.

■ Final bonding strength is reached

after a very short time (approx.

2 minutes)!

■ Spot glueing is recommended on long

items with large surfaces.

■ Rigid foam (e.g. polystyrene) can also

be glued without a problem. Merely

remember to apply the hot glue on

the base surface and not on the

polystyrene.

■ When glueing textiles or similar

materials, it is recommended to

apply the hot glue in "wavy" lines.

■ Let the applicator cool down

after use.

Charging / Operation

The rechargeable battery in the neo 2

comes partially charged. Before using

the applicator for the first time, fully

charge the battery (approx. 2-3 hours) to

ensure full capacity.

The neo 2 cannot be used while it is

charging.

Interrupting the charge cycle will not

damage the rechargeable battery. The

battery can be recharged at any time

without shortening its lifespan.

"Electronic Cell Protection (ECP)"

protects the battery from exhaustive

discharge. If the battery runs flat, pro-

tective circuitry switches the neo 2 OFF

and glue is no longer heated.

Charging with USB charger

Button LED red LED green

ON/OFF Battery charging

Applicator ready for use for a limited period

Battery is fully charged, charge cycle is completed

Operation / glueing

Button LED red LED green

ON Switch ON. Press button for approx. 2 sec.

Green LED ﬂashes for 15 sec.

Applicator ready for use

Applicator starts for a further 5 min. each time you

press the trigger

No glueing for 5 min.

Applicator switches OFF

Switch applicator back ON at button

Red and green LED ﬂashes alternately after

applicator has been in use for approx. 20 min.

The applicator can now only be used for approx.

another 10 min.

Red LED ﬂashes 1x

Battery ﬂat, start charging using USB charger

Dimensions (HxWxD): 157 x 47 x 158 mm

Power supply: 100-240 V, 50/60 Hz, micro-USB charger

Battery voltage: 3.6-V lithium-ion rechargeable battery

Heating-up time: under 15 seconds

Rechargeable-battery run time: approx. 30 minutes (continuous operation)

Battery charging time: 90% in 3 hours

Melt temperature: approx. 170 °C

Recommended glue sticks: genuine STEINEL

Crystal sticks, Prod. No 040413 /

Ultrapower sticks, Prod. No. 0405005

(Ø 7 mm)

Technical Specifications

1 2 3 4 5 6 7 8 9 10 11 ... 66 67

Comments to this Manuals

No comments

STEINEL NEO2 Operations Instructions Page 6

Comments to this Manuals

Related products and manuals for Cordless glue guns STEINEL NEO2