STEINEL sensIQ S Specifications download pdf (Page 8)

- 15 -- 14 -

Reach setting 햾

(Factory setting: max. reach)

Functions using the infrared remote control

Any number of sensIQ S units can be operated

by remote control.

Note: Each sensIQ has no more than one

remote control. The remote control must be

programmed when used for the first time.

To do this, button must be pressed within

10 min. of switching on the power supply. This

operation can be repeated as often as desired.

The last remote control saved always applies.

The following special functions are presented

as follows:

Holiday function: LED rapidly flashes

3x every 5 sec.

Manual override: LED permanently ON

Permanently OFF: LED flashes every 2 sec.

Film shrouds 햴

If the independent settings of the 3 sensors are not sufficient, the detection zone can restricted

further by fitting film shrouds C, D, E (see Fig.). Film shrouds A + B under the sensor help to prevent

the detection of small animals. This, of course, takes the lenses out of action and in particular

results in loss of the sneak-by guard.

Note: The remote control does not work when using film shroud A (see Fig. 햴).

Advice: Apply a solution of water and detergent to the lens before fitting the film shroud.

This way, the film does not firmly stick on immediately and gives you time to make precision

adjustments. Once the cleaner is dry, the film adheres.

max

1.8 m

2 m

4 m

8 m

13 m

19 m

>20 m

2.5 m

2 m

4 m

7 m

12 m

16 m

>20 m

3 m

7 m

12 m

>20 m

–

5 m

4 m

12 m

>20 m

–

Stan-

dard

Twilight setting

(response threshold) 햻

(Factory setting: daylight

operation 2000 lux)

The sensor's response threshold can be set to

between approx. 2 lux and 2000 lux.

Note:

The desired twilight value can also be

memorised by remote control.

Time setting

(switch OFF delay) 햽

(Factory setting:

approx. 10 sec.)

The time you wish the con-

nected light to stay ON for

can be infinitely adjusted from approx. 5 sec.

to a maximum of 15 min.

Pulse mode:

Set the control dial to " " the unit is in pulse

mode, i.e. the output is switched ON for

approx. 2 sec. (e.g. for staircase lighting timer).

Afterwards, the sensor does not react to

movement for approx. 8 sec.

Functions on the unit

The system can be put into operation once the

mains power has been connected and the unit

is closed. The sensor first goes through a cali-

bration cycle (40 – 50 sec.) (LED flashes once

a second).

Several settings can then be made directly on

the sensor or by remote control (see Remote

control).

5 sec. – 15 min.

2 – 2000 lux

Setting,

control dial

2 – 20 m

1)1)

1) Not recommended, limited detection

Mounting

height

Functions using infrared remote control RC 1

Holiday function:

The holiday function gives the impression that

someone is at home. Once the light-level

threshold is reached, the connected load is

programmed to switch ON and OFF again after

approx. 3 hours. Normal sensor mode remains

active.

LED indicator: rapidly flashes 3 x every 5 sec.

Permanent light OFF:

Pressing this button switches the connected

load OFF for 6 hours. After this period, the

sensor returns to sensor mode automatically.

LED indicator: permanently ON

Reset function:

Pressing this button once quits the holiday,

manual override and permanent OFF functions.

The previously set values apply again.

Manual override:

Pressing this button switches the connected

load ON for 4 hours. After this period, the

sensor returns to sensor mode automatically.

LED indicator: permanently ON.

Twilight setting by the potentiometer

on the device:

Pressing this button reactivates the light level

set on the sensor. As soon as you change the

light-level setting directly on the sensor, this

value takes effect. Any adjustments of the

remote control are ineffective.

Twilight setting by memory button:

This button must be pressed at the level of

light at which you want the sensor to respond

to movement from now on. The current twilight

value is saved.

SENSOR

Reach can be adjusted in 3 directions by 3 control dials (through 100° in each direction and

independently of each another). The table shows reaches at different mounting heights for

tangential walking direction. The values apply on flat terrain at a temperature of 20° C.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments to this Manuals

No comments

STEINEL sensIQ S Specifications Page 8

Comments to this Manuals

Related products and manuals for Motion detectors STEINEL sensIQ S