STEINEL RS 16 L Specifications download pdf (Page 8)

- 15 -

Troubleshooting

SensorLight without power

SensorLight will not switch ON

SensorLight will not switch OFF

SensorLight switches on without

any identifiable movement

SensorLight does not switch ON

despite movement

Malfunction

 House fuse faulty, not switched ON,

break in wiring

 Short circuit in mains power supply

lead

 Any mains switch OFF

 Renew house fuse, switch ON

mains power switch, check wiring

with voltage tester

 Connect connections

 Switch on mains power switch

 Wrong twilight setting selected

 Bulb faulty

 Mains switch OFF

 House fuse faulty

 Adjust setting

 Change bulb

 Switch ON

 Renew house fuse,

check connection if necessary

 Continuous movement

in the detection zone

 Check zone setting

 Light mounting surface is subject to

vibration

 Movement occurred, but not identi-

fied by the sensor (movement behind

wall, movement of a small object in

immediate lamp vicinity etc.)

 Securely mount enclosure

 Check zone setting

 Rapid movements are being sup-

pressed to minimise malfunctioning

or the detection zone you have set

is too small

 Check zone setting

Cause Remedy

The SensorLight can be put into operation as soon as

the enclosure  has been fitted and the SensorLight

has been connected to the mains power supply.

Putting the light into operation manually at the light

switch turns it off after 10 secs. for the calibration

phase. Once calibrated, it is activated for the sensor

mode. It is not necessary to operate the light switch a

second time.

Reach setting (sensitivity)

Reach is the term used to describe the

diameter of the more or less circular

detection zone produced on the

ground after mounting the sensor

light at a height of 2.5 m. Turn the

reach control  fully anticlockwise to

select minimum reach (approx. 1 m

dia.)*, and fully clockwise to select maximum reach

(approx. 8 m dia.)*. (The light leaves the factory set to

maximum reach.)

Time setting (switch-off delay)

The light can be set to stay ON for

any period of time between approx.

5 sec. (control  turned fully anti-

clockwise) and a maximum of 15 min.

(control  turned fully clockwise).

(The light leaves the factory set to the

shortest time.) Any movement detect-

ed before this time elapses will re-start the timer. It is

recommended to select the shortest time for adjusting

the detection zone and for performing the walk test.

Note: After the light switches OFF, it takes approx.

1 sec. before it is able to start detecting movement

again. The light will only switch on in response to

movement once this period has elapsed.

Twilight setting (response threshold)

The chosen light response threshold

can be infinitely varied from approx.

2–2000 lux. Turn control  fully anti-

clockwise to select dusk-to-dawn

operation at about 2 lux. Turn control

 fully clockwise to select daylight

operation at about 2000 lux. (The

light leaves the factory set to daylight operation.) The

control must be turned fully clockwise when adjusting

the detection zone and performing the walk test in

daylight.

Functions

- 14 -

1 m – 8 m dia.*

Functional Warranty

This STEINEL product has been manufactured with

great care, tested for proper operation and safety in

accordance with applicable regulations and then sub-

jected to random sample inspection. STEINEL guar-

antees that it is perfect condition and proper working

order. The warranty period is 36 months, starting on

the date of sale to the consumer. We will remedy

defects caused by material flaws or manufacturing

faults. The warranty will be met by repair or replace-

ment at our own discretion. The warranty shall not

cover damage to wear parts, damage or defects

caused by improper treatment or maintenance.

Further consequential damage to other objects is

excluded.

Claims under the warranty will only be accepted if the

unit is sent fully assembled and well packed complete

with a brief description of the fault, a receipt or

invoice (date of purchase and dealer's stamp) to the

appropriate Service Centre.

Repair Service:

Our Customer Service Department

will repair faults not covered by

warranty or after the warranty period.

Please send the product well

packed to your nearest Service

Centre.

Declaration of conformity

This product complies with

- Low Voltage Directive 2006/95/EC

- EMC Directive 2004/108/EC

- RoHS Directive 2002/95/EC

- RTTE Directive 1999/05/EC

5 sec. – 15 min.

2 – 2000 lux

* 3 – 8 m dia. (RS 15 L, RS 16/16-2/16-3 L)

BDAL Serie RS_24spr_neu 27.07.2011 11:06 Uhr Seite 15

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 51 52

Comments to this Manuals

No comments

STEINEL RS 16 L Specifications Page 8

Comments to this Manuals

Related products and manuals for Ceiling lighting STEINEL RS 16 L